DynaVap 2021 M Starter Pack

The 2021 M features the stainless steel captive cap that was introduced on the M last year and it holds tightly onto this year's totally redesigned tip. You'll notice the exterior of the tip sports a complicated and drastically upgraded design compared to the last model. It's designed to give you superior airflow and channel air around the entire tip, rather than just through a couple of paths like on the 2019 M tip. It also more efficiently heats air before it moves into the extraction chamber, which is going to give you better vaporization performance and less unwanted cooling of your chamber, meaning you get a better hit throughout the heat cycle.

At the very end of the tip you’ll see the new septa crown, it features seven cutouts of the same depth, and it doesn't have that same sharp edge as the 2020 tip. If you keep in mind this theme of seven you’ll find a number of related Easter eggs on this device, let me know all of the different ways you see the number seven utilized on this one, I can find quite a few.

Inside the tip you'll find the dual position adjust-a-bowl, I highly recommend that you experiment with the smaller bowl position, you’ll end up saving a ton of flower while still getting a very similar experience. It’s the only way I use mine now.

Further down the tip is the new incremental fin profile which also plays on the theme of sevens. You'll notice that the fins are wide at the bottom and get thinner as they move towards the top. These fins help to provide more cooling as the vapor moves down through the device while retaining heat in the extraction chamber for a more consistent session. The very top fin creates a donut shaped air channel between the bottom of the cap and the tip that preheats incoming air and slows the airflow down a little bit, so that the preheating action is more effective.

The tip connects to the body of the device with three o-rings and it slides in and out very easily, with the past models it’s sometimes been a bit tricky to get the tip in and out, but DynaVap have improved the tolerances on the new 2021 M.

This airport is by far the coolest that DynaVap have ever put on an M. This is the next generation chiral airport, meaning that it is separated into two sections like on the 2020 M, rather than just a single hole. There is some seriously precise machining going on here, the M shaped chiral airport is carved in steps or layers into the metal. Not only does this look super cool, but these subtle details also help to serve the goals of increased airflow complexity and more effective mixing of the warm extraction air with the cool dilution air. I love how it looks straight up like an M, front and centre on the device, it’s by far my favorite airport design yet.

I was a big fan of the rocker on the 2020 M and how it made that Metallica-ish M on the back, that’s been replaced this year with a compounded angle rocker. It doesn’t look as cool, but it’s definitely way more functional, it reminds me a little of the rocker on the OmniVap but it’s not quite the same. It's designed with the same purpose as the hourglass profile, to help your fingers naturally fall into place and to eliminate the need to hunt and grope after the heat up.

Between the chiral airport and the new rocker you get fantastic back-and-forth airflow, you can hear how well it functions as you rock the device between your fingers. The airflow complexity and the back-and-forth nature helps to disrupt the straight laminar, on or off sort of airflow to help enhance your hit.

One thing which seems counterintuitive, but I highly recommend you try, is to heat it up low on the cap and then take a hit without putting your fingers over the airport at all. You’d think that this would result in too much airflow and a small hit, but I am blown away by the size of the clouds that this method produces and the hits are also nice and cool because you're getting so much airflow. Give it a go when you’re trying that smaller bowl position.

The mouthpiece is designed to fit perfectly into a 10mm female joint, so it’s ready to use with a water piece, no need for an adapter unless you want to use it with a 14 mm water piece. I would recommend either a Fat Mouthpiece or one of our Master Adapters for this purpose.

Just above the mouthpiece there’s one more machined section which provides a place to grip, but this area is not only functional, it’s also somewhat of a fingerprint from the machine used to create these devices. What that means is that each 2021 M is slightly unique, I think it’s a neat little touch.